The encoded stream is then transmitted through the
stream mode channel of the existing Eureka-147
DAB system. RS encoder use RS(204, 188, t=8)
shortened code derived from the original systematic
RS(255, 239, t=8) code as in the DVB-T system
(ETSI, 2001). By adding the additional FEC and
interleaving, the target bit error rate (BER) of the
system is improved from the level of
4
10
−
to
8
10
,
and by which high quality mobile video service is
possible through the Eureka-147 DAB system which
is originally designed for CD quality audio data
transmission. Fig. 2 shows the total transmission
system for T-DMB including the Eureka-147
transmission blocks.
Stream mode data channel
OFDM
Modulator
Multi-
plexer
Fast information channel
Service information
DAB audio frame channel
Packet mode data channel
Eureka-147 transmission system
Convolutional
interleaver
RS
encoder
MPEG-2 TS
multiplexer
Encoded
data
T-DMB processor
MPEG-2 TS
Figure 1: Structure of the T-DMB system.
T-DMB
Encoder
Outer
interleaver
Outer
Coder
MPEG-2 TS
Scrambler
Conv.
Encoder
Time
Interleaver
MSC
Multiplexer
OFDM
Modulator
Frame
Multiplexer
Eureka - 147
Figure 2: Transmission system of T-DMB.
2.2 DVB-SH System Architecture
The DVB-SH system is developed to provide
multimedia services over hybrid satellite and
terrestrial networks to a variety of fixed or mobile
terminals including handheld, vehicle-mounted,
nomadic and stationary terminals at frequencies
below 3 GHz. It has a universal coverage by
combining a satellite component and a
complementary ground component. In the DVB-SH
system, there are two architectures applying two
modulation methods: SH-A for OFDM terrestrial
and OFDM satellite transmission mode, and SH-B
for OFDM terrestrial and TDM satellite transmission
mode.
Figure 3 shows the two architectures for different
modulation method (ETSI, 2007). As shown in the
figure, the two transmission systems are designed to
maximize the commonalities between them. OFDM
transmission mode is mainly based on the existing
DVB-T or DVB-H systems, while TDM
transmission mode is mainly based on DVB-S2
system. Main blocks newly introduced by DVB-SH
includes strong FEC and longer time interleaver
which aims to overcome long fading events under
the low signal-to-ratio mobile satellite and terrestrial
environments. The final sentence of a caption should
end with a period.
2.3 DVB-SH System Incorporating the
T-DMB
One of the purpose in incorporating the T-DMB
system into DVB-SH systems is to maximize the
commonalities between the existing T-DMB and
DVB-SH systems in order to maximize hardware
reuse. The DMB processor in the T-DMB system
correspond to the IP encapsulator in the DVB-SH
system. However, MPEG-2 TS data are processed
by RS encoder in a DMB processor while the output
of the encapsulator, which performs RS coding and
interleaving, has the form of MPEG-2 TS. Moreover
the error correction capability in the two systems are
different. In DVB-H, by passing the multi-protocol
encapsulation (MPE) with RS(255, 191) coding, the
RS decoder allows correcting up to 32 erroneous
bytes (Balaguer , 2005). Instead RS decoder gives 8-
byte correcting capability in T-DMB system by
using RC(204, 188) code (Lee, 2005). Therefore, we
cannot input the output of the DMB processor
instead of the output of the IP encapsulator in the
DVB-SH system.
One method to provide T-DMB contents
simultaneously or similarly via DVB-SH network is
input the DMB processor output as an input to the
DVB-SH, that is, as an input of the IP encapsulator.
In this case, the Eureka-147 transmission part in the
T-DMB system is replaced with the DVB-SH
architecture. Therefore, modularization of the
common hardware block is possible between the T-
DMB and DVB-SH systems.
Another method to provide T-DMB contents is
input the MPEG-4 sync layer (SL) encapsulated data
of DMB processor, designated by encoded data in
Figure 1, to the input of the IP encapsulator. In this
ON THE DVB-SH SYSTEM ARCHITECTURE
167